Just how to Replace a Bathtub ( Guide).
Just how to Replace a Bathtub ( Guide).
Blog Article
Every person will have their private rationale about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Installing a tub isn't specifically rocket science, however it does call for solid plumbing, woodworking, and often, tiling abilities. Replacing an old tub with a brand-new one is also a moderately tough task. If the old tub is easily easily accessible, the task can relocate quickly; if you need to open up a wall surface to remove the old tub as well as place the brand-new bathtub, the task is much harder. In either situation, the task is within a residence handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also embeded in the brand-new one. See to it you have actually certified on your own for the work and fit attempting it. Rather than hiring a service provider to take control of a halfway-completed task, it is much better to think about employing one before you start. Opportunities are you may need a professional plumber to make tube connections.
This short article will help you install a brand-new bath tub in your washroom if you have actually already purchased a new tub and do not require to change the arrangement of your previous water supply pipelines.
Your devices as well as material checklist should consist of the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your installment, after that the first thing you ought to do is disconnect the water system. After doing so, switch on the taps to drain pipes any kind of water continuing to be in the system. The process of removing the existing faucets can be fairly troublesome due to the limited accessibility that is typically the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the continuing to be water that will come from the pipelines. When the supply pipes have actually been eliminated, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. As soon as the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old sealing compound.
Prior to carrying on to fit the new taps, contrast the pipeline links on the old taps to the new taps. If the old faucets are longer than the new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic port to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end offers a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in place in between the tap as well as the sink. Safeguard the tap in position with the maker provided backnut. When the tap is safely in place, the supply pipes can be attached to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The former kind should be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Bath tub
Using the two wood boards under its feet, position the bathtub in the needed placement. The wooden boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 tiny points.
The next goal is to make sure that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the bath tub until the spirit level checks out degree.
To install taps, fit all-time low of the outermost adaptable faucet connector to the appropriate supply pipe by making a compression join; after that do the very same for the various other faucet.
Switch on the water and examine all joints and also brand-new pipework for leakages and also tighten them if essential. Load the bath tub as well as likewise inspect the overflow electrical outlet as well as the typical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling as well as sealing around the tub ought to wait up until the tub has been used a minimum of once as this will settle it into its last placement.
Planning for the Installment
To start with, the sustaining structure provided with the bath ought to be fitted (if required) according to the producer's instructions. Next, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is very important to ensure that if the tap comes with a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent pressure on the bath tub.
Fit the versatile tap connectors to the bottom of both faucets utilizing 2 nuts and olives (sometimes provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the provided washers.
Attach the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final position.
Tiling Around the Tub
In the area where the bathroom satisfies the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to split a rigid seal, triggering the water to penetrate the wall surface between the bathroom and the tiling, bring about problems with wetness as well as feasible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures and also fittings. They are offered in tubes and cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the bath tub with water before sealing, to permit the movement experienced when the bathtub is in use. The sealer can crack relatively very early if you do not consider this motion prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally easily offered on the marketplace. It is advisable to fit the ceramic tiles making use of water-resistant or waterproof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a reader about How to Install a Bathtub Yourself, I figured sharing that excerpt was beneficial. Remember to set aside a second to share this entry if you liked it. Thanks so much for going through it.
Source This Article Report this page